







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Irvine, CA: What It Costs and How Long It Takes
Most tub-to-shower conversions in Irvine run $3,500 to $10,000 and take 7 to 14 working days from demolition to final walkthrough. The job involves pulling the old tub, reworking the drain and valve wall as needed, waterproofing, setting a new shower pan and tile, and passing inspection – which in this city means clearing your HOA’s architectural committee before a single tile gets ordered. Call (833) 954-6066 and we’ll walk you through the scope on your specific bathroom.
Stage by stage: how a tub-to-shower conversion actually runs

Every conversion follows the same spine, but the pace depends on what’s behind the wall. Here’s the real sequence, with what you decide and when.
Stage 1 – Estimate and HOA check (days 1 to 5, before demolition)
We measure the alcove, photograph the tub and valve wall, and put a written line-item quote in your hands – a fixed number, not a range that drifts. This is also when you pull out your village’s CC&Rs. In Irvine, a bathroom change that touches only the interior usually stays out of architectural review, but townhomes and condos in Woodbridge and Northwood often have plumbing-access and quiet-hour rules that shape our schedule. You decide on tile and fixture selections here, because lead times on special-order pans and glass run two to three weeks.
Stage 2 – Demolition and rough-in (days 6 to 8)
Out comes the tub, the surround, and the old backer board – roughly one to two days with dust control and floor protection. We open the valve wall and inspect the drain. This is the moment that decides your budget: a cast-iron tub on a 1970s slab is heavier and slower to remove, and a valve buried in corroded galvanized pipe means the rough-in grows. You see photos before we close anything up.
Stage 3 – Plumbing, framing and inspection (days 8 to 9)
We set the new shower valve, extend or relocate the drain to the center of the new pan, block the walls for grab bars, and set the pan. Where the rough-in changes, we pull the permit and meet the inspector. You decide here whether to add a bench, a niche, or a linear drain – all of it easier now than later.
Stage 4 – Waterproofing and tile (days 9 to 12)
Liquid or sheet membrane goes on, then a flood test where the scope calls for it, then the tile. Pan tile and wall tile usually take two to three days with grout and cure time. This is the slow part, and it’s the part you don’t rush. Your only decision now is grout color and whether the curb stays or disappears in favor of a curbless entry.
Stage 5 – Glass, trim and walkthrough (days 12 to 14)
We hang the glass enclosure, reset the fixtures, seal, and walk the room with you. You get a punch list and a written record. The 730-Day Done Right Promise covers the workmanship from that day forward – if something isn’t right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
- Acrylic or fiberglass pan and wall kit: the fast, budget-friendly path. Fewer seams, no grout to scrub, installed in a couple of days. The honest trade-off is a limited color palette and a plastic feel that won’t win an HOA design review on a townhome exterior-facing bathroom window wall.
- Tile over a waterproofed pan: the sweet spot for most Irvine homes. You pick the pan (prefab or mud-set), the membrane system, and the tile. Costs land mid-range, holds up for decades, and matches the house. Takes the longest of any option.
- Curbless and low-threshold entries: the right call if you’re planning for aging in place or a family member with mobility needs. It means recessing the floor or building a gentle slope, which pushes the job toward the top of the range.
- Glass enclosure style: framed, semi-frameless, or frameless. Frameless glass from a supplier like Mr-Glass reads cleanest in a small Irvine bathroom; it’s also the priciest and needs a square, plumb opening to look right.
- Fixture grade: a builder-grade valve versus a thermostatic Kohler or similar. The valve is buried in the wall, so upgrading now costs less than tearing tile later.
- Bench, niche, and grab-bar blocking: small additions, permanent value. Blocking costs almost nothing during framing and a lot afterward.
What Tub-to-Shower Conversion costs in Irvine, CA

Plan on $3,500 to $10,000 for a tub-to-shower conversion in Irvine. A straightforward acrylic conversion in a standard alcove sits near the bottom. A tiled, curbless, glass-enclosed shower with upgraded fixtures and a relocated drain lands near the top.
Five things move the number:
- Alcove size and shape: a standard 60-inch tub opening is the cheapest to convert. Odd dimensions mean custom pans and glass.
- Plumbing condition: reusing the existing drain and valve keeps costs down. Moving the drain or replacing corroded pipe adds labor and permit scope.
- Structural changes: removing a wall, widening the opening, or recessing the floor for a curbless entry is framing work, not finish work.
- Material grade: acrylic kit versus tile, prefab pan versus mud-set, builder valve versus premium fixture.
- Permit scope: a finish-only swap may not require one; moving plumbing does. We pull it and pass the inspection when the scope needs it.
Your written estimate itemizes demo, rough-in, waterproofing, tile or kit, glass, and permit. It excludes surprises we can’t see until the wall opens – and we tell you that before we start, not after. No change orders you didn’t approve, and the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Irvine homes specifically do to this job
Irvine is a master-planned city, and that changes a bathroom conversion in ways it wouldn’t in a city of older, ungoverned lots. Nearly every home sits inside an HOA-governed village with architectural review and CC&Rs, so in older villages like Woodbridge and Northwood we’re matching original tract design vocabulary, and in Great Park builds we’re working to contemporary standards. Interior tile and fixtures are usually yours to pick, but a shower that changes a window, vent, or exterior wall can pull the architectural committee into the conversation before the city permit. Townhomes bring party-wall and plumbing-access rules that set our hours.
The housing stock matters too. Most of these are 1970s to 2000s wood-frame tract homes and condos, and the oldest bathrooms are reaching the age where the valve wall is due. We regularly find corroded galvanized stubs behind a 1970s tub in Turtle Rock, or a fiberglass surround that’s been quietly leaking into the subfloor for years. That’s the failure we see most. It’s why we open the wall and show you before we quote the rough-in.
Serving Irvine, CA – Our Local Coverage Area
We serve Irvine and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Tub-to-Shower Conversion in Irvine

Seven to fourteen working days, with most Irvine projects landing around ten. The range depends on tile versus acrylic kit, whether we relocate the drain, and how fast glass and special-order pans arrive. Call (833) 954-6066 for a schedule based on your bathroom.
If the drain or valve moves, yes – plumbing rough-in requires a permit and an inspection. A finish-only swap over an existing drain may not. We confirm the scope for your address and pull the permit when it applies, so the work closes out clean.
Usually, yes. Most standard 60-inch tub alcoves convert to a shower over the existing drain location. We only move plumbing when the pan size, a curbless entry, or a failed drain line forces it, and you’ll know the cost before we open the wall.
Between $3,500 and $10,000, depending on pan type, tile versus kit, glass style, and whether plumbing moves. Call (833) 954-6066 for an exact quote – estimates are free and itemized.
The 730-Day Done Right Promise backs the workmanship for two years after we hand over the room – if it’s not done right, we make it right. Material warranties come from the manufacturers. Every project gets that same written guarantee, no exceptions.
Ready to price your Irvine conversion?
Call (833) 954-6066 for a free on-site estimate on your tub-to-shower conversion in Irvine. We’ll measure the alcove, open a conversation about your HOA and permit scope, and hand you a written line-item quote with a fixed price – no vague ranges. Financing at 0% for 18 months is available, and projects over $10,000 take $1,000 off. If you’re folding this into a bigger job, our Bathroom Remodeling in Irvine page shows the wider scope, and we cover the whole city from Woodbridge to Great Park – see our Irvine service area. Homeowners often pair this with exterior work like Metal Roofing in Irvine or Tile Roofing in Irvine, and you can explore our full Bathroom Remodeling service too.
Written by the team at Groundwork Construction Co.












