







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Irvine, CA: What It Involves and What It Costs
Metal roofing in Irvine, CA typically runs $15,000 to $40,000 for a full residential install, and most projects take 4 to 7 working days once materials are on site. That timeline is longer than a shingle job because the panels are cut to fit, the subflute ventilation has to be built correctly, and in nearly every Irvine village the work sits behind an HOA architectural approval before the city permit is even pulled. Call (833) 954-6066 to schedule a free on-site estimate and we’ll walk the roofline with you, measure the actual square footage, and give you a written line-item quote.
How We Run a Metal Roofing Job, Stage by Stage

Here’s the real sequence, in the order it happens, so you know what to expect on day one versus day five.
Stage 1: Inspection and HOA packet (days 1 to 10, before we touch the roof)
We measure the roof, check the existing underlayment, and photograph any decking that’s soft. In Irvine, this is also when your HOA architectural committee packet gets assembled: panel color, profile, and finish samples all get submitted with the CC&R application. Approval timelines vary by village, so this is usually the longest single step in the project, and it happens before demolition. You’ll pick your panel color at this stage.
Stage 2: Tear-off and deck inspection (days 1 to 2 of construction)
We remove the existing roofing material down to the deck and inspect the sheathing. On 1970s and 1980s Woodbridge and Northwood homes, we regularly find fascia board with dry rot from long Santa Ana summers that baked the timber, particularly on south and west-facing slopes. Any rot gets replaced before panels go down. You’ll approve any deck repair costs at this point, and we don’t proceed without your sign-off.
Stage 3: Underlayment and flashing (days 2 to 3)
We install a high-temp synthetic underlayment rated for the heat that builds under metal in Irvine’s dry climate, then set the eave trim, valley flashing, and ridge venting. This is where most cheap metal jobs fail: skipping proper ventilation causes condensation under the panels, which corrodes the deck over time. We build it to spec so the panels last as designed.
Stage 4: Panel installation (days 3 to 6)
Panels are cut and set per the approved design. Standing seam panels go down in long runs for fewer seams; exposed-fastener panels go down faster with screws and washers at each joint. Ridge caps and closures go on as the panels go up, so the roof is watertight each night. You don’t need to be home for this stage; we send photo updates daily.
Stage 5: Final inspection and cleanup (day 6 to 7)
We sweep for stray screws and metal shavings, since those rust into stucco and stain landscaping if left behind. Then the city inspection happens. In Irvine, the final sign-off requires the panel manufacturer’s warranty documentation, so we hand you the paperwork before we leave the property.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Metal roofing isn’t one product. These are the real choices that come up in Irvine, with what each one costs in durability and look.
- Standing seam steel: the premium choice, with concealed fasteners and 40-plus year manufacturer warranties when installed to spec. Best for homeowners planning to stay 15 years or more. Higher upfront cost, fewer service calls.
- Exposed-fastener steel panels (R-panel): the most budget-friendly metal option and common on agricultural and utility buildings; washers fail on the fasteners in 15 to 20 years, so it’s a shorter-horizon choice.
- Stone-coated steel: a steel panel sprayed with stone granules so it mimics tile or shake. Popular in HOA villages where full tile profile is required but weight matters. The coating can chip, so choose matte finishes over glossy.
- Aluminum panels: lighter and naturally rust-resistant, well-suited to Irvine’s dry climate and the ocean air that drifts inland. Softer than steel, so hail and foot traffic dent it more easily.
- Color and finish: Kynar 500 or equivalent fluoropolymer paint holds color in UV-heavy Southern California better than basic polyester finishes. A faded roof looks old before it is old.
What Metal Roofing Costs in Irvine, CA

A full standing seam metal roof on a typical Irvine home runs $15,000 to $40,000. Here’s what pushes a job toward either end of that range.
Roof size and pitch. A 1,800 square foot roof on a low-pitch single-story home stays near the low end. A two-story with multiple hips, valleys, and dormers on a steep pitch costs more, because panels are harder to cut and more material is wasted.
Deck condition. If the existing sheathing is sound, that’s easy. If we’re replacing rotted fascia and decking, add cost. Older Northwood and Woodbridge homes are most at risk for this.
Material choice. Aluminum panels cost more than basic steel; stone-coated panels cost more than plain steel but less than standing seam. Fluoropolymer finishes are worth the upcharge.
Tear-off and disposal. Removing existing tile or shingles and hauling it costs included in most quotes but priced separately on some.
HOA and permit scope. Standard Irvine permits are routine; if your village requires additional architectural submittals or special inspections, that adds time and fees.
Your written estimate covers tear-off, underlayment, flashing, ventilation, panels, ridge caps, cleanup, and permit. It doesn’t typically cover deck rot beyond a set allowance, or skylight replacement. We state that allowance clearly instead of surprising you with change orders.
See the difference
Before
After
Before
After
Before
AfterWhat Irvine Homes Specifically Do to a Metal Roofing Job
Irvine is a master-planned city, and that shapes every metal roofing project here. Your HOA architectural committee dictates the approved panel color, profile, and finish, and in older villages like Woodbridge and Northwood, that means matching the original tract design vocabulary. Great Park and newer village builds are held to contemporary standards, so the approved profile set is different. The result: we spend as much time with your architectural committee as with the building inspector. A crew showing up with the wrong panel color gets stopped before the first one is installed. Your ZIP code (92602, 92604, 92617, 92619) tells us which village guidelines apply before we pitch.
The housing stock adds a second wrinkle. Irvine is overwhelmingly 1970s to 2000s wood-frame stucco homes with tile roofs. The oldest villages are now at the age where re-roofing is routine, and we regularly find baked fascia and dried-out sheathing under the original tile. The semi-arid climate – hot Santa Ana winds and long rainless stretches – bakes wood and stucco, then winter storms reveal flashing failures in the first big rain. Metal roofing holds up better in that cycle than tile because panels don’t crack or grow algae the way clay does.
Serving Irvine, CA – Our Local Coverage Area
We serve Irvine and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Irvine

Most Irvine metal roofing projects take 4 to 7 working days of on-site construction, plus 1 to 3 weeks for HOA approval and city permits before work starts. The panel type and roof complexity drive the spread. Call (833) 954-6066 for a timeline estimate specific to your home.
Yes, a building permit is required for any re-roof in Irvine, and in HOA-governed villages you also need architectural committee approval before the city will issue the permit. We handle both. Call (833) 954-6066 and we’ll walk you through what your specific village requires.
Occasionally, a metal panel system can be installed over existing roofing with proper underlayment and structural review, but most Irvine homes we see do better with a full tear-off. Tear-off lets us inspect the deck and fix rot. Call (833) 954-6066 for a free estimate and we’ll tell you which approach fits your home.
Most Irvine metal roofing projects fall between $15,000 and $40,000, depending on roof size, pitch, panel type, and deck condition. Stone-coated steel sits lower in that range, standing seam aluminum higher. Call (833) 954-6066 for a written line-item quote – estimates are free.
A new metal roof typically boosts resale value and reduces insurance premiums compared with a failing tile or shingle roof, and it holds up impressively in Santa Ana wind events where tile can crack. It’s often part of a full Roofing in Irvine upgrade homeowners pair with Window Replacement in Irvine and, sometimes, Impact Windows & Doors in Irvine. Call (833) 954-6066 for a free estimate that covers the whole exterior envelope.
Get Your Free Metal Roofing Estimate
If you’re ready to price a metal roofing project on your Irvine home, call (833) 954-6066. We’ll schedule a free on-site estimate, measure the roof, explain which panel profiles your village HOA typically approves, and hand you a written line-item quote with a fixed price. Our technicians have up to 12 years of experience, and every job carries our 730-Day Done Right Promise. From foundation to finish line, we handle the full scope – explore our broader Roofing services and the communities we serve across Irvine. Calls are answered by a live person 24/7.
Written by the team at Groundwork Construction Co.












