







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Custom & Geometric Windows in Tustin, CA: What to Expect
Custom & geometric windows in Tustin, CA run $6,500 to $22,000 for a typical whole-house package of shaped or non-standard units, with most single feature windows in the $1,200 to $4,500 range depending on glazing, frame material, and how the rough opening has to be built. The job takes four to seven weeks from signed contract to final inspection, because every geometric unit is made to order and nothing is stocked in a warehouse. Call (833) 954-6066 for a free on-site estimate and a written line-item quote.
Here’s what most people get wrong up front: a custom arch, trapezoid, or full-height rake window isn’t a bigger version of a standard slider. It’s a template job. Someone measures the opening, the factory builds a one-off unit to that template, and the window arrives weeks later ready only for that exact hole.
How we handle a custom or geometric window job, stage by stage

Because these units can’t be returned or reordered cheaply, the front half of the job carries most of the decisions. Here’s the actual sequence.
Stage 1: On-site measure and feasibility (day 1, about 90 minutes)
We open up the wall cavity or inspect the existing unit, check the stud layout, and confirm what’s behind the drywall. You’ll decide then whether you’re duplicating an existing shape or introducing a new one. We photograph the opening, note header conditions, and flag anything that might need structural work before a template can be cut. This is also when we walk you through the samples so you’re choosing frame material and glazing with a real window in hand, not a catalog photo.
Stage 2: Template and order (days 1 to 3)
A template is cut in place for arch, radius, and trapezoid units, because a tape measure won’t capture a curve honestly. From that template the factory builds your unit, usually four to six weeks out for geometric shapes and three to four weeks for large rectangular custom sizes. You’ll sign off on the final specification sheet, glazing package, and hardware at this stage. This is the decision point that seals the price. Any change after the order goes in means a new unit and a new lead time.
Stage 3: Rough opening prep and framing (day of install, morning)
When the unit lands, we remove the old window or frame the new opening from scratch. That means verifying the header, squaring the rough opening to the template, and adding blocking where the unit needs to fasten. On a new opening we’ll often need to rough in before drywall and stucco go back. This is where the schedule lives or dies, because a rough opening that’s out of square by a quarter inch shows up as a visible gap around a curved frame.
Stage 4: Setting, flashing, and sealing (same day, afternoon)
The unit gets set, leveled, shimmed, and fastened to the template dimensions. Flashing detail on the exterior matters more on geometric units because water has more places to collect – the shoulders of an arch, the corners of a trapezoid. We flash and seal before any trim goes on, and we check the drainage plane works. Then the interior trim, casing, and finish work goes in. Most single-window jobs close out in one day; a full package takes two to three.
Stage 5: Inspection and punch list (within a week)
If the job pulled a permit, we schedule the inspection and meet the inspector on site. Then we walk the job with you, check operation and locking hardware on every unit, and confirm the finish work is right before we call it done. Anything that isn’t right gets corrected under our 730-Day Done Right Promise – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between
Custom and geometric windows aren’t a single material choice; they’re a stack of three or four choices that each shift the price and the look. Here’s where the real trade-offs sit.
- Frame material – wood, aluminum-clad wood, vinyl, or fiberglass. Wood gives you the cleanest radius and the sharpest corner on a trapezoid, and it’s the natural fit for Old Town’s Spanish Revival and Craftsman stock – but it takes maintenance. Aluminum-clad wood (Andersen and Marvin both build geometric units in clad wood) gives you the wood interior and a weatherproof exterior, and it’s the most common choice for arched feature windows. Vinyl works for standard rectangles but struggles to hold a tight curve without visible weld lines. Fiberglass holds dimension well and handles heat, at a premium over vinyl.
- Glazing package. Double-pane Low-E with argon is the baseline now. Tustin’s hot, dry summers and Santa Ana wind events push a lot of homeowners toward a solar-control coating on west and south elevations, which adds cost but cuts heat gain. Tempered glass is required any time the window is within a certain distance of a door or floor – a code call we make in the field, not a preference.
- Shape and size. A half-round transom over a door is one of the cheaper custom units. A full-height arch, a circle, or a multi-unit mulled assembly of angled windows climbs fast. Each seam where two units join is a place that can leak, so we keep assemblies as simple as the design allows.
- Muntins and divided lites. Simulated divided lites give you the interior grille look on a custom shape without the cost of true divided glass. On a curved window, grilles have to be custom bent, so expect the cost to jump the moment you add them.
What Custom & Geometric Windows cost in Tustin, CA

Plan on $6,500 to $22,000 for a multi-window custom package, or $1,200 to $4,500 for a single feature window installed. A straightforward half-round transom with a stock frame sits near the bottom. A full assembly of arched, mulled, clad-wood units with custom grilles sits at the top, and can run past $22,000 once you add structural framing and finish work on three or four openings.
The variables that push a job toward the high end:
- Unit size and shape complexity. Every curve and angle adds fabrication and a template step. A rectangle is a rectangle; a radius is a one-off.
- Rough opening condition. Replacing a window in a sound opening is one thing. Cutting a new opening in a load-bearing wall, reframing a header, or correcting an out-of-square opening adds labor and often engineering.
- Structural or finish work. If the opening needs a new header, new drywall, new stucco, or a repair to the exterior finish, that’s a separate line item. We don’t hide it.
- Glazing and finish grade. Solar-control coatings, tempered glass, custom interior trim species, and exterior paint or stain all add up.
- Permit scope. A straight replacement in the same opening is often exempt from a permit. Changing the size or location of an opening usually isn’t, and the inspection adds time and a fee.
A written line-item estimate from us lists each unit, glazing spec, frame material, installation labor, and any framing or finish work as separate lines. What’s not included in the base number: painting and staining, window treatments, and any structural repair found after the wall comes open. We tell you those are allowances up front, so the number you see is the number you pay unless the wall reveals something nobody could see. No-hassle upfront pricing, no change-order surprises.
See the difference
Before
After
Before
After
Before
AfterWhat Tustin homes specifically do to this job
Tustin’s window work is split between two very different jobs a few miles apart. In the Old Town core, we’re working on 1920s Craftsman and Spanish Revival bungalows where the original openings are rarely square, the framing is old, and a geometric window often has to be built to fit an opening that has settled over a century. Those homes also need the wall checked for knob-and-tube wiring and old plumbing before we open anything up, because it’s cheaper to find it during the estimate than mid-install. In Tustin Legacy, on the former MCAS Tustin airfield land, the work is new construction – ground-up framing where the geometric window is spec’d from a plan and the rough opening is built to the template, not measured against an existing wall. Contractors in that district also deal with the two WWII blimp hangars, still among the largest wooden structures in the world, which means historic-structure sensitivity and brand-new site work can sit within a few blocks of each other.
Climate shapes the choice too. Our semi-arid Mediterranean weather brings hot, dry summers and Santa Ana wind events that slam west- and south-facing glass with sun and heat, so solar-control glazing matters here more than the catalog suggests. The mild wet winters, when it rains hard, are when a badly flashed arch shows its flaws. We detail flashing like the rain is coming, because eventually it is.
This is part of a larger scope for a lot of Old Town homeowners, and if you’re reworking the whole exterior at once, that wider project lives on our Windows & Doors in Tustin page. You can also see our full Windows & Doors service for the standard replacement side of the work. If the driveway is getting torn up by the same project, Concrete Driveways & Concrete Work in Tustin and Asphalt Driveways & Resurfacing in Tustin get scheduled alongside it so the yard comes back together in one pass. We cover all of Tustin, and our windows & doors service reaches North Tustin, Irvine, Aliso Viejo, and Anaheim as well.
Serving Tustin, CA – Our Local Coverage Area
We serve Tustin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Custom & Geometric Windows in Tustin

Four to seven weeks from signed contract to final inspection. Most of that is factory lead time: four to six weeks for geometric units, three to four for large custom rectangles. The install itself is usually one day for a single window and two to three days for a full package. Call (833) 954-6066 for a timeline specific to your openings – estimates are free.
Often yes, if the opening changes size or location. A same-size replacement in an existing opening is frequently exempt, but cutting a new arched opening in a wall, reframing a header, or changing egress triggers a permit and inspection. We pull the permit for you and meet the inspector on site. Call (833) 954-6066 and we’ll tell you what your specific job needs before you commit.
Usually yes, if the opening already exists. The trouble comes when the shape or size changes enough to touch a header or a wall cavity carrying plumbing or wiring. We check that during the on-site estimate and tell you honestly before you sign. Call (833) 954-6066 to schedule a free assessment of the opening.
Around $1,200 to $4,500 for a single feature window, and $6,500 to $22,000 for a multi-window package. Shape complexity, frame material, glazing, framing work, and permit scope are what move it. Call (833) 954-6066 for an exact quote – estimates are free and come as a written line-item.
Every job is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right, for two years from completion. That covers workmanship and installation. The window manufacturer’s warranty covers the unit itself, and we hand you the paperwork. Call (833) 954-6066 with any warranty question before or after the job.
Get a free estimate for Custom & Geometric Windows in Tustin
Call (833) 954-6066 and a live person answers, day or night. We’ll set a free on-site estimate, measure the opening, show you frame and glazing samples, and put together a written line-item quote with the number you see and the number you pay. Project over $10,000? Take $1,000 off, plus 0% financing for 18 months if you want it. From foundation to finish line, built to last and backed in writing.
Written by the team at Groundwork Construction Co.












