







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Tustin, CA: What It Takes and What It Costs
A wrought iron fence in Tustin typically runs $3,500 to $9,000 installed, and most residential jobs are done in three to five working days once the layout is set. The work moves fast because iron is modular: posts go in, panels hang on them, and a finish coat goes on before the gate ever swings. Call (833) 954-6066 and we’ll walk your property line, confirm the footage, and put real numbers on paper – free, no pressure.
How We Build an Iron Fence, Start to Finish

Iron fencing punishes sloppy prep. Concrete footings that aren’t deep enough heave in Tustin’s dry-wet swing, and a post set an inch off plumb throws off every panel downstream. Here’s the sequence we actually run, stage by stage, and where you make the calls.
Day 1: Walk, layout, and utility locate
We mark the run with string and stakes and confirm the exact footage, gate placement, and corner posts with you before anything gets dug. We also call for the utility locate – a mandatory step before a shovel touches soil, since water, gas, and irrigation lines run close to the property line in most Tustin lots. You decide the gate swing direction and latch side here; changes after this point cost more.
Day 1-2: Demolition and footing prep
If an old fence comes out, we pull it the first morning and haul it off. Post holes get dug on a set spacing – usually 6 to 8 feet on center, tighter on gates where the load carries. Footings get poured with concrete and left to cure. In summer heat that cure runs faster; in a wet Tustin winter we may hold a day. You don’t have to make a decision at this stage, but this is when the real labor happens.
Day 2-3: Posts set and rails anchored
Cured posts get set plumb and braced, then the top and bottom rails go on. This is the structural stage, and it’s where a cheap job shows. We check plumb with a level on every post rather than eyeballing it, because iron doesn’t forgive a lean. You’ll see the shape of the fence now, which is your window to confirm the layout still feels right.
Day 3-4: Panels, pickets, and gate hang
Pickets or panels drop into the rails and get secured. The gate gets its hinges, latch, and any self-closing hardware. Pool-safety gates, if that’s part of the run, need to swing and latch correctly at this point – we test them open and closed. You’ll try the gate yourself before we finish.
Day 4-5: Finish coat, touch-up, and walk-through
Any weld or cut marks get a rust-inhibiting touch-up, and we do a final pass on hardware and alignment. Then we walk the whole run with you: gate tension, latch engagement, finish quality, and the clean-up. Anything on that walk that isn’t right, we fix before we call it done.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Actually Choose Between
Iron fencing isn’t one product. The choices below are the ones that legitimately change how your fence looks, how long it lasts, and what you pay.
- Wrought iron vs. tubular steel vs. aluminum: True wrought iron is heavy, welded, and the premium pick; it’s the most expensive and the most durable. Tubular steel is a strong middle option. Aluminum is the lightest and cheapest, resistant to rust, but dents more easily on impact. For a front-yard statement fence, wrought iron or steel; for a long side-yard run on a budget, aluminum earns its place.
- Picket spacing: Standard spacing (usually around 4 inches) satisfies most pool-safety codes and keeps pets in. Tighter spacing looks more solid and costs more material; wider decorative spacing is cheaper but lets small dogs through.
- Height: 4-foot, 5-foot, and 6-foot runs are the common heights. Taller fences cost more in material and labor and can trip HOA review.
- Finish: Powder-coated black is the standard and holds up well under Tustin’s hard summer sun. Bare or hot-dip galvanized finishes cost less up front but rust faster in wet winters. Custom colors exist but add cost and lead time.
- Gates: A single walk gate is standard. Double-drive gates, self-closing pool gates, and automated gates each add cost – an automated gate can add a few thousand dollars once the operator and wiring are in.
- Decorative details: Finials, scrollwork, and custom panels are where a fence turns into a feature. They add cost per linear foot, so budget for them only where it’s visible.
What Iron Fence Costs in Tustin, CA

Plan on $3,500 to $9,000 for a residential iron fence in Tustin, installed. That range covers the fence, posts, footings, gates, and finish. Where a job lands depends on five things:
- Linear footage: The single biggest driver. A short front-yard run sits near the low end; a full property perimeter pushes to the high end.
- Material grade: Aluminum at the low end, steel in the middle, wrought iron at the top.
- Gates and hardware: Each gate adds cost; automated or self-closing hardware adds more.
- Site conditions: Removing an old fence, working around concrete, or digging in rocky soil all add labor.
- Finish and details: Powder-coat standard, custom colors and decorative panels on top.
A written estimate from us breaks the job into line items: footage, post count, gate count, footing depth, finish, demo, and haul-away. What typically isn’t included is landscape repair after digging, HOA review fees, and any work to relocate utilities if a line sits right on the fence line – none of which we surprise you with mid-job. The number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Tustin Homes Specifically Do to This Job
Tustin runs two extremes side by side, and iron fencing feels both. In Old Town, the 1920s Craftsman and Spanish Revival bungalows sit on tight lots with mature landscaping, old irrigation lines, and sometimes century-old hardscape right on the property line. We dig carefully there and layout around existing trees and patios, not through them. Out in Tustin Legacy, the master-planned development on the former Marine Corps Air Station Tustin footprint, the fencing runs along newer lots where soil and grading are still settling in – so footing depth and post stability get extra attention. Tustin’s semi-arid climate matters too: hot, dry summers with Santa Ana wind events bake exterior finishes, and wet winters expose any footing that wasn’t set deep enough. A powder-coated finish holds up under that cycle; a cheap finish doesn’t. If a new iron fence is part of a full Fence Installation in Tustin project across front and side yards, we plan the whole run together. Homeowners often pair this with Patios, Walkways & Pool Decks in Tustin, since a fence and a patio share the same excavation and grading work. If your lot line is moving because of a new structure, our ADU Design & Permitting in Tustin team coordinates the layout so the fence lands where code wants it.
Serving Tustin, CA – Our Local Coverage Area
We serve Tustin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Iron Fence in Tustin

Most residential iron fence jobs run three to five working days from layout to final walk-through. A short front-yard run can finish in two or three; a full perimeter with multiple gates stretches toward a week. Weather and utility locates are the usual swing factors. Call (833) 954-6066 for a schedule estimate on your lot.
Fence permits depend on height, location, and whether it fronts a pool – most low residential fences don’t require a permit, but pool barriers and taller runs can. We confirm the requirement for your specific address before we dig rather than guessing. Call (833) 954-6066 and we’ll sort out what your property needs.
Yes. A well-run iron fence job is limited to the post holes and the trench line, so the yard stays largely intact. We route the run to preserve existing landscaping where we can and haul off any demo debris. Call (833) 954-6066 to walk your layout.
Expect $3,500 to $9,000 for a residential iron fence installed, with footage, material grade, and gate count driving the difference. Wrought iron and custom detailing sit at the top of that range; aluminum runs at the bottom. Call (833) 954-6066 for an exact figure – estimates are free.
Every iron fence we build is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That’s one of the longest workmanship guarantees in residential construction. Call (833) 954-6066 for the full written terms.
Get a Free Iron Fence Estimate in Tustin
We’ll come out to your property, walk the run, and hand you a line-item quote – the footage, the material, the gates, the finish, the numbers. No charge, no obligation. You’ll know exactly what an iron fence costs for your lot before you commit to anything. Call (833) 954-6066 to schedule your free estimate. Our technicians have up to 12 years of experience, and we answer the phone with a live person, 24/7.
Written by the team at Groundwork Construction Co. of Tustin.












